Difference between revisions of "S15: Hand Gesture Recognition using IR Sensors"

Latest revision as of 03:43, 25 May 2015

Abstract

The aim of the project is to develop hand gesture recognition system using grid of IR proximity sensors. Various hand gestures like swipe, pan etc. can be recognized. These gestures can be used to control different devices or can be used in various applications. The system will recognize different hand gestures based on the values received from IR proximity sensors. We have used Qt to develop the application to demonstrate the working of the project.

Objectives & Introduction

We use various hand gestures in our day-to-day life to communicate while trying to explain someone something, direct them somewhere etc. It would be so cool if we could communicate with various applications running on the computers or different devices around us understand the hand gestures and give the expected output. In order to achieve this, we are using a 3-by-3 grid of analog IR proximity sensors and connecting these sensors via multiplexers to the ADC pins on SJOne Board. As a hand is moved in front of the sensors, the sensor values would in a particular pattern enabling us to detect the gesture and instruct the application to perform the corresponding action.

Team Members & Responsibilities

Harita Parekh
- Implementing algorithm for gesture recognition
- Implementation of sensor data filters
Shruti Rao
- Implementing algorithm for gesture recognition
- Interfacing of sensors, multiplexers and controller
Sushant Potdar
- Implementation of final sensor grid
- Development of the application module

Schedule

Week#	Start Date	End Date	Task	Status	Actual Completion Date
1	3/22/2015	3/28/2015	Research on the sensors, order sensors and multiplexers	Completed	3/28/2015
2	3/29/2015	4/4/2015	Read the data sheet for sensors and understand its working. Test multiplexers	Completed	4/04/2015
3	4/05/2015	4/11/2015	Interfacing of sensors, multiplexers and controller	Completed	4/15/2015
4	4/12/2015	4/18/2015	Implementation of sensor data filters Implement algorithm to recognize left-to-right movement	Completed	4/25/2015
5	4/19/2015	4/25/2015	Implementation of final sensor grid Implement algorithm to recognize up-to-down movement Implement algorithm to recognize right-to-left movement	Completed	5/02/2015
6	4/26/2015	5/02/2015	Implement algorithm to recognize down-to-up movement Develop the Qt application	Completed	5/09/2015
7	5/03/2015	5/09/2015	Testing and bug fixes	Completed	5/15/2015
8	5/10/2015	5/16/2015	Testing and final touches	Completed	5/22/2015
9	5/21/2015	5/24/2015	Report Completion	Completed	5/24/2015
10	5/25/2015	5/25/2015	Final demo	Scheduled	5/25/2015

Parts List & Cost

SR#	Component Name	Quantity	Price per component	Total Price
1	Sharp Distance Measuring Sensor Unit (GP2Y0A21YK0F)	9	$14.95	$134.55
2	STMicroelectronics Dual 4-Channel Analog Multiplexer/Demultiplexer (M74HC4052)	3	$0.56	$1.68
3	SJ-One Board	1	$80	$80
4	USB-to-UART converter	1	$7	$7
Total (excluding shipping and taxes)				$223.23

Design & Implementation

Hardware Design

The image shows the setup of the project.

Figure 1: Setup of the project

System Block Diagram:

The system consists of 9 IR proximity sensors, which are arranged in 3x3 grid. The output of the sensors is given to the Analog-to-Digital convertor on the SJOne Board to get the digital equivalent of the voltage given by the sensors. Since there are only 3 ADC channels exposed on the pins on the board, we cannot connect all the sensors directly to the board. For these we have used three multiplexers, which has 3 sensors each connected to its input. The output of the multiplexers is connected to ADC. SJOne board is connected to the laptop via UART-to-USB connection.

Figure 2: System Block Diagram
*Proximity Sensor:* This sensor by Sharp measures the distance from an obstacle by bouncing IR rays off the obstacle. This sensor can measure distances from 10 to 80 cms. The sensor returns an analog voltage corresponding to the distance from the obstacle. Depending on which sensor returns valid values, validations could be made and hand movement can be determined. The voltage returned by the sensor increases as the obstacle approaches the sensor. There is no external circuitry required for this sensor. The operating voltage recommended for this sensor is 4.5V to 5.5V.	Figure 3: IR Proximity Sensor
*Multiplexer:* The chip used in the project is M74HC4052 from STMicroelectronics. This is a dual 4-channel multiplexer/demultiplexer. Due to shortage of ADC pins to interface with the sensors, use of multiplexer is required. The multiplexer takes input from three sensors and enables only one of them at the output. The program logic decides which sensor’s output should be enabled at the multiplexer’s output. A and B control signals select one of the channel out of the four. The operating voltage for the multiplexer is 2 to 6V.	Figure 4: 4-Channel Dual Multiplexer
USB-to-UART converter: To communicate to SJONE board over UART there is a need an USB to serial converter and a MAX232 circuit to convert the voltage levels to TTL, which the SJONE board understands. Instead it’s better to use a USB-to-UART converter to avoid the multiple conversions. This is done using CP2102 IC, which is similar to a FTDI chip.	Figure 5: USB-to-UART chip

Hardware Interface

Pin connections for IR Sensor to Multiplexer:

Figure 6: Pin connections for IR Sensor to Multiplexer

Pin connections on SJOne board:

Figure 7: Pin connections on SJOne board

Connections between SJOne board and USB-to-UART Converter:

Figure 8: Connections between SJOne board and USB-to-UART Converter

Software Design

Initialization

SJOne board has 3 ADC pins exposed on Port 0 (0.26) and Port 1 (1.30 and 1.31). To use these pins as ADC, the function should be selected in PINSEL.

The GPIO pins on Port 2 are connected to the select pins on multiplexer. These pins should be initialized as output pins. Once, initialization is completed, the function for normalizing the sensor values is called.

Figure 9: Flowchart for initialization of ADC and multiplexer

SJOne board uses UART 3 to communicate with the QT application. UART 3 is initialized to baud rate of 9600 with receiver buffer as 0 and transmission buffer as 32 bytes. Once initialization is completed, the function for processing sensor values is called.

Figure 10: Flowchart for initialization of UART and process

Filter Algorithm

The current value of sensor is fetched by setting the corresponding values on the multiplexer select pins and reading the output of the ADC. A queue of size 5 is maintained and the fetched value is inserted at the tail of the queue. This queue is sorted using bubble sort. The median value of the queue is checked to be greater than 2000 (sensor returns a voltage corresponding to a value greater than 2000 when the hand is near enough to it) and gesture array for that sensor is set accordingly.

Figure 11: Flowchart for filter algorithm

Gesture Recognition Algorithm

Different sets of sensors are monitored in order to recognize a valid pattern in the sensor output and thereby recognize the gesture pattern.
(We have assumed that the sensors are numbered 0 through 8 and the corresponding value for the sensor is set by the filter algorithm in gesture[] array).

Pattern 1:

Figure 12: Flowchart for selection of pattern 1

Here the three sensors present at the top left corner are monitored.

If sensor1 value is zero
- Check the values of sensors in the second column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the third column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Right” to UART 3.

If sensor3 value is zero
- Check the values of sensors in the second row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the third row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Down ” to UART 3.

Pattern 2:

Figure 13: Flowchart for selection of pattern 2

Here the three sensors present at the top right corner are monitored.

If sensor1 value is zero
- Check the values of sensors in the second column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the first column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Left ” to UART 3.

If sensor5 value is zero
- Check the values of sensors in the second row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the third row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Down ” to UART 3.

Pattern 3:

Figure 14: Flowchart for selection of pattern 3

Here the three sensors present at the bottom left corner are monitored.

If sensor7 value is zero
- Check the values of sensors in the second column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the third column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Right ” to UART 3.

If sensor3 value is zero
- Check the values of sensors in the second row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the first row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Up ” to UART 3.

Pattern 4:

Figure 15: Flowchart for selection of pattern 4

Here the three sensors present at the bottom right corner are monitored.

If sensor7 value is zero
- Check the values of sensors in the second column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the first column. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Left ” to UART 3.

If sensor5 value is zero
- Check the values of sensors in the second row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Check the values of sensors in the first row. If the combination of first two or last two sensors is 1, go to next step. Else, update the gesture array for these sensors and check.
  - Send “Up ” to UART 3.

Application Development
Qt Software

Qt is a cross-platform application framework that is widely used in developing application software that can be run on various software and hardware platforms with little or no change in the underlying codebase while having the speed and the power of native application.

It is mainly used to make GUI based applications but there can be applications such as consoles or command-line applications developed in Qt. Qt is preferred by many application programmers as it helps in developing GUI applications in C++ as it uses the standard C++ libraries for backend.

Platforms supported by Qt are:

Android
Embedded Linux
Integrity
iOS
OSX
QNX
VxWorks
Waylands
Windows
Windows CE
Windows RT
X11

Qt applications are highly portable from one platform to other as Qt first runs a Qmake function before compiling the source code. It is very similar to ‘cmake’ which is used for cross platform compilation of any source code. The qmake auto generates a makefile depending on the operating system and the compiler used for the project. So if a project is to be ported from windows to linux based system then the qmake auto generated a new makefile with arguments and parameters that the g++ compiler expects.

Figure 16: Devices supporting Qt

Figure 17: Qt-SDK

Gesture Recognition application on Qt

Once the gesture is recognized on the SJONE board, a message is sent over UART3 stating which gesture was sensed. The Qt application gets this message from the COM port and scrolls the images left and right based on the left/right gesture and it moves a vertical slider up and down which in turn changes the value on a LCD screen display.

The application opens up in a window that has 2 tabs, config and App. The config tab includes the fields required to open the COMM port and test the COMM port using a loopback connection.

Figure 18: Configuration Tab

This tab has the following QObjects.

Table 1: QObjects used for Configuration Tab

The App tab includes the objects required to change images and change the value in the vertical slider and lcd number display.

Figure 19: Application Tab

This tab has the following Qobjects.

Table 2: QObjects used for Application Tab

Implementation

Application Logic

The below diagram shows the setup of the files used in the project.

Figure 20: Code Structure tree diagram

The main function creates the tasks required for the application namely, SensorTask, WaitTask and ProcessSensor.

Figure 21: Main file snippet

The tasks are declared in Hand_Gesture.hpp file.

Figure 22: Header file snippet

This file also includes the enumerations required in the program logic.

sensorNo_t: This enumeration assigns numbers to the sensor from 0 through 8.
portPins_t: This enumeration assigns the shifting logic to P2_0 through P2_5 for better readability.

Hand_Gesture.cpp file contains the definitions of all the functions as listed below.

Figure 23: Source File snippet showing the function defined

The WaitTask is used internally in ProcessSensor to wait for values of sensor to change while navigating through the above described algorithm. This task enables the system to wait for maximum of 5 seconds to receive any change of values in the sensor. If after 5 seconds, the sensor values are not as desired by the algorithm (to proceed to next stage), the sensor values are concluded to be false positives and further execution is skipped.

The constructor of SensorTask includes the initialization of pins for ADC and Port 2 pins used as select lines for the multiplexer.

Figure 24: Pin initialization

UART 3 is initialized using the Singleton pattern.

Figure 25: UART initialization using Singleton Pattern

The init function of UART is used to initialize UART 3 to communicate at the baud rate of 9600. Since the application will only be sending values to the Qt application and not expecting any replies, the receive buffer is set to zero and the transmission buffer is set to 32 bytes.

Figure 26: UART driver initialization

Qt Application Implementation

Includes and app initialization
This sections includes all header files required for the app and the constructor and destructor for the app. As we are displaying multiple images in the app the path of these images have to be hardcoded. We also define an enum to capture the received gesture. An instance of the serial port is also created in the constructor, and an initial welcome image (SJSU logo) is displayed on the app.

Figure 27: Snippet of initialization

Configuration COM port
The COM port is configured in this section of the code, the name of the COM port and the baud rate is picked up from the lineEdits present on the config tab and passed to populate the structure of the serial port. If there is an error opening the COM port then an error message is displayed. The COM port is closed once the disconnect button is pressed.

Figure 28: Configuration of COM port

Serial receive and loopback test
This section includes the code to copy all the data received in the receive buffer parse it and take the decision on which kind of gesture was received and take the appropriate decision. The loop back section picks up anything written on the Tx lineEdit and displays the received buffer on the rx lineEdit.

Figure 29: Code to test serial receive using loopback

Open Image
The logic to switch between images and to loop through the images is implemented here.

Figure 30: Code to switch between images

Scroll
The position of the vertical slider is changed depending on the up/down gesture, the LCDnumber display is used to display the position (value) of the vertical slider. The value ranges from 0-99 and loops through if the value is greater 99 or smaller than 0.

Figure 31: Code to scroll the vertical slider

Setup and Working

Sensor setup

Figure 32: Sensor setup

Screenshots of Qt application

Figure 33: Configuration screen

Figure 34: Application screen

Testing & Technical Challenges

Challenge #1:

The sensor produces many spikes giving false positive outputs.

Resolution:

In order to overcome spikes received and deal with false positive, normalization of the sensor output is done. A circular queue of size 5 is maintained for each sensor and each value received from the ADC is stored at the end on the queue. This queue is then sorted and only the median value is considered for computation. This reduces the false positives to a great extent.

Challenge #2:

Number of sensors used was far greater than the available ADC pins.

Resolution:

Even if we had 9 ADC pins converting values of 9 sensors, we would still be reading the each sensor one by one. Keeping this in mind, in order to overcome the deficit of ADC pins, we have used multiplexer which takes the input from 3 sensors at a time and gives the output of only the selected sensor. In this way, we could read the output of any sensor at any given point of time. The introduction of multiplexer introduces a lag but this lag is not long enough to hinder the operation of the application.

Challenge #3:

Qt being a new application for all the team members, it was a challenge to learn its programming style and use the objects.

Challenge #4:

Setting up the serial port communication in Qt.

Conclusion

Gesture recognition using IR sensors was a very interesting and challenging project. The main areas where we enjoyed working were the development of the gesture recognition algorithm and sensor filter algorithm. This project increased our knowledge in:

Developing filters for analog sensors
Working with the sensor itself
Reading datasheets for the multiplexer and sensor
Hands-on experience in Qt application
Using Singleton pattern for UART

This project was developed in a small scale. Further work can be done to integrate this project in devices, which would help blind people to use software, which require manual intervention, seamlessly.

Project Video

Gesture Recognition using IP Proximity Sensors

Project Source Code

Sourceforge Source Code Link

References

Acknowledgement

All the components where procurred from Amazon, Adafruit and digikey. We are thankful to Preet for his continuous guidance during the project.

References Used

IR Sensor Data Sheet
LPC_USER_MANUAL
Multiplexer Data Sheet
QT Software
Filter code refered from Spring'14 project Virtual Dog