| Week#
|
Date
|
Planned Task
|
Actual
|
Status
|
| 1
|
9/23/2017
|
- Decide roles for each team member
- Read FY16 project reports and understand requirements
- Setup Gitlab project readme
- Ordered CAN Tranceivers and get R/C car
|
- Team roles are decided and module owners are assigned
- Gitlab project is set
- Ordered CAN tranceivers and got R/C Car
|
Complete.
|
| 2
|
9/30/2017
|
- Design software architecture for each module and design signal interfaces between modules
- Setup Wiki Project Report template
- Design Hardware layout of system components
- Create component checklist and order required components for individual modules.
- Setup Gitlab project code for each modules
|
- Overall project requirements are understood
- Wiki Project report setup is done
- Odered components for Geo controller module
- Initial commit of project base is done
|
Complete
|
| 3
|
10/14/2017
|
- Major Feature: Implement Free run mode
- Implement heartbeat messages and initial system bootup sync between modules
- Interface the RPLidar to SJOne board via UART
- Achieve basic communication such as obtaining the device and health info.
- Study of Android Toolkit for Bluetooth Adapter connections and APIs
- Study of HC-05 Bluetooth Module
- Creating APIs for Start/ STOP button requests to write to output-Stream buffers
- Creating RFComm SPP Connection socket and the rest of UI for basic operation of Pairing, Connection
- Checking the AT Command sequence for Bluetooth Operation and Pairing
- Automating the AT Command sequence for Bluetooth HC-05 operation and Android App
- Run Motors via commands from SJOne Automatically
- Order the RPM sensor module for the Drive Controller
- Design and Order PCB
|
- Major Feature: Implemented Free run mode
- Added hearbeat messages from all controllers to master in can_db and implemented the handling functions in master controller
- Implemented speed steer command CAN msg transmission and handling in Master controller. Master-Drive integration phase-I
- Interfaced RPLidar to SJOne board and achieved basic communication via UART. Started obtaining data as well.
- Android:Android API for Bluetooth Adapter connections studied.
- Android:Learning of AT Command sequence for Bluetooth Operation and Pairing done.
- Android:Created Start/Stop API's for button requests to be Sent to HC-05 IC.
- Android:Basic Pairing Operation Working.
- Motor: ESC Traxxas XL-5 (Electronic Speed Control) interfaced to SJOne board
- Tested and identified duty cycles for different speeds required; Callibration and testing of ESC is over exteral switch at P0.1
- Ordered RPM sensor
|
Complete
|
| 4
|
10/21/2017
|
- Major Feature: Implement Basic Obstacle Avoidance in Free-run mode
- Add all modules CAN messages to DBC file
- Test steer and speed CAN commands between Master and Motor
- Implement Obstacle avoidance algorithm
- Obtain data from the lidar and process the data i.e. decide on the format in which the data has to be sent to the master
- Write unit test cases for the lidar.
- Interface compass module to SJOne board and calibrate the errors
- find the heading and bearing angle based on mocked checkpoint
- Test and verify GPS module outdoor to receive valid data and check for errors
- Calibrate the GPS module error
- Design and implement the DRIVE_CONTROLLER STEER/SPEED interface with Master (TDD)
- Install the new RPM sensor module for the Drive Controller
- Operating motors based on the CAN messages from the Master
|
- Major Feature: Implemented Free-run mode w/o obstacle avoidance
- Added all modules basic CAN messages in can_db
- Implemented interface files in master controller to handle CAN messages from all nodes to master
- Implemented Master-Drive controller Integration
- Implemented Master-Bluetooth controller integration
- Added all modules basic CAN messages in can_db
- GPS integrated to SJONE board
- Added all modules basic CAN messages in can_db
- Wrote unit test cases for the LIDAR.
- Wrote logic for dividing the information obtained from the lidar into sectors and tracks.
- MASTER_SPEED_STEER_CMD was defined to use 8-bits for speed control (neutral, forward, and reverse); 9-bits for steer control (straight, left, and right)
- Designed glue code: DriveManager and hardware interface code: DriveController using TDD (test code in _MOTOR/_cgreen_test/)
- Got the Traxxas #6520 RPM sensor; installed the same with the slipper clutch; Observed the RPM sensor trigger over an oscilloscope and found the minimum distance of magnet to RPM sensor is not achievable with the stock slipper clutch. Ordered Traxxas #6878 new slipper clutch and ball-bearings
- Master - Drive Controller Interface implemented and tested over CAN; Check "drive" terminal command on Master controller
|
complete
|
| 5
|
10/28/2017
|
- Major Feature: Implement maneuvering in Master controller
- Implement maneuvering algorithm to drive steering angle of the servo
- Implement maneuvering algorithm to control ESC speed
- Test and validate the information obtained from the sensor.
- Send the Lidar data and heartbeat over CAN.
- LIDAR should be fully working.
- Identify the basic speed(s) at which the car shall move; the min, max and normal forward speeds, and the min and normal reverse speeds
- Interface the RPM sensor over ADC and validate the readings
- Writing PID Algorithm for Motor Control
- Calibrating PID constants according to the Motors
- Testing the Bluetooth Range and multiple pairing option to establish security of the Master device
- Testing the accuracy of GPS while moving
- Made the code modular and added the wrapper function for all the important modules
- Worked on android app which will dump the lattitude and longitude information for checkpoints
- Test the accuracy of GPS while moving
- Get the code review done and do the testing after that
- Worked on the Android app that will dump the checkpoints into a file
- Finish PCB design and place order
|
- Major Feature: Implemented maneuvering in Master-Geo controller
- Major Feature: Implemented Basic Obstacle Avoidance in Free-run mode
- Implement maneuvering algorithm in android app is moved to next week schedule
- Implemented maneuvering algorithm in Master to drive steering angle of the servo
- Implement maneuvering algorithm in Master to control ESC speed
- Unit Testing obstacle avoidance algorithm
- Tested and validated the sensor data by plotting graphs in an EXCEL sheet.
- Sending the obstacle information and heartbeat over CAN.
- LIDAR fully working and sending obstacle information.
- Identified basic speeds, slow, normal, and turbo for forward and reverse
- Interfaced the RPM sensor over GPIO and validated; but the clutch gear with magnet was far apart from the RPM Sensor
- Wrote the PID code keeping future integration in mind; Have pushed the code
- Failed to use RPM sensor - new clutch gear also did not work (magnet is too far away - validated with Oscilloscope); Have to consider using IR sensor for feedback
- Android:Tested successfully individual and multiple Device pairing.
- Android:Android app updated with Navigation and Drawer Modules with Detecting NAV points.
- Tested the accuracy of GPS while moving
- Made the GPS and compass code modular and checked the functionaity after the changes
- Worked on the Android app that will dump the checkpoints into a file
- Completed PCB Design
|
Complete
|
| 6
|
11/07/2017
|
- Major Feature: Implement maneuvering with mocked GEO checkpoints
- Collect mock checkpoints using the Android Data Collector application
- Collect mock checkpoints using the GEO module and compare for any discrepancies
- Identify I/O on-board Display information; Currenly identified are documented below:
- Health status like GPS Lock status, etc.
- Identify hardware to check battery-status and procure the same; update PCB as well
- Display bluetooth pairing status
- Test on-board I/O module for bluetooth pairing status
- In case RPM installation/usage fail, Identify new mechanism for feedback and order components; Update PCB as well to include new hardware
- Implement simple feature additions on steer control to handle reverse; basically steering rear-left and rear-right has to be practically implemented on motor/drive controller
- Receive GEO Controller's Turning-angle message and compute target steer
- Use GEO Controller's distance to next-checkpoint information to compute target speed
- Mock checkpoint navigation testing using different possible obstacle heights and forms possible
- Identify advertisement messages on the DBC file and add documentation in Wiki; Currently identified advertisements: a) current GEO location, b) SENSOR radar map
- Shall define the BLE Controller to android message structure and message generation-intervals (classify on-demand advertisements and periodic advertisements)
- Implement marker for current location display - which is an on-demand advertisement
- Implement feature for the user to enter destination - a Google Map View shall be shown to the user to confirm route from source(current car location) to destination
- Android app (once on the new device) shall download the entire offline map information of the SJSU campus and store it on a SQLite database
|
- Major Feature: Implemented maneuvering with mocked GEO checkpoints
- Provided Mock checkpoints and used the heading and bearing angle logic to get the turning angle
- Collected mock checkpoints and check for the error with different places
- Interfaced the Sparkfun Seven segment display with the SJOne Board.
- Implemented interface method to receive GEO Controller's Turning-angle message and set target steer
- Target speed is not changed between checkpoints.So geo feedback for distance to destination is not used in design
- Destination Reached flag is tracked to stop the car on reaching destination
- Checkpoint Id CAN signal is processed by Master to start the car once destination is selected
- Android:Implemented Marker for current position Display.
- Android:User entry for setting up destination on MAP done.
- RPM Installation failed, but could get auxiliary hardware (motor pinion) from local shop and get it working
- Implemented basic motor feedback using hall sensor (RPM sensor); tested working on ramps
- Steer left and right on reverse now follows natural order; Could not finish literal reverse-left and reverse-right implementation; Moved this task forward; Had to test and implement motor feedback this week
- Defined the BLE Controller messages to android in JSON message structure and message generation-intervals (classify on-demand advertisements and periodic advertisements)
- On Demand Advertisement- Current Marker Location
- Draggable Destination Marker for final destination and intermittent checkpoint transmission to GEO from Android via BLE
- Marking the checkpoints with HUE_BLUE color to do better tracking of the navigation.
- Added multi state BT options and Added restrictions on buttons like NAV usage dependency on BT Connection, Powerup button dependency on NAV setup before actually powering the car.
|
Complete
|
| 7
|
11/14/2017
|
- Major Feature: Implementing maneuvering with Android app supplied GEO checkpoints with on-board I/O
- Use mock data from file to compute: a) Heading b) Bearing -> use Haversine's algorithm to compute turning angle
- Advertise distance to the next checkpoint (again using Haversine's algorithm)
- Save the proper checkpoints for one route (Clark's to SU) to SDCARD on GEO Controller
- Implement system start/stop triggers from different use cases
- Turning angle offset of -10,10 is added to take right / left turn
- Implement the battery-status DBC Message advertisement
- Indicate checkpoint proximity using backlight indicators
- Create 2 CAN messages for Disgnostic and I/O data to transmit it to BLE module
- Receive the diagnostic CAN message and decode to transmit it to Android App
- [Android I/O:] Design Android app views for visualizing Diagnostic and I/O data
- Test and validate success/fail cases for on-board I/O display information(as defined above)
- Update PWM pulses to match MASTER's target speed with proper feedback from the identified feedback-mechanism
- Identify PID constants kp, ki, kd and evaluate performance against the basic feedback implementation
- Finalize feedback algorithm and fine-tuning
|
- Major Feature: Implemented maneuvering with Android app supplied GEO checkpoints with on-board I/O
- [Geo:] Implemented mock data from file to compute: a) Heading b) Bearing -> used Haversine's algorithm to compute turning angle
- [Geo:] Advertised distance to the next checkpoint (again using Haversine's algorithm)
- [Geo:] Saving the checkpoints in SDCARD on GEO Controller
- Implemented start-stop triggers from android and auto start on start of route navigation
- Turning angle from geo is handled with offset
- battery-status is optional feature. Planning for later
- Indicate checkpoint proximity using backlight indicators
- [BLE:] Created CAN messages for Telemetry data from all modules to BLe to send to Android
- [BLE:] Received Telemetry messages are transmitted to Android App
- [Android I/O:] Android app views created for visualizing Telemetry data
- Test and validate success/fail cases for on-board I/O display information
- Update PWM pulses to match MASTER's target speed with proper feedback from the identified feedback-mechanism
- Finalize feedback algorithm and fine-tuning
|
Complete.
|
| 8
|
11/21/2017
|
- Major Feature: Complete maneuvering implementation with Android app and Android I/O
- [Android I/O:] Implement display of Sensor Obstacle Information on a RADAR map
- [Android I/O:] Dynamically update car's Current location on the map's route path
- [Android I/O:] BT Auto Connection and Pairing implemented
- [Android I/O:] Health information from BLE Controller, namely battery, GPS lock status, and motor speed shall be updated
- [Android I/O:] BT Auto connect implementation and re-connection on disconnection.
- Test achievable target speeds with different possible obstacle heights and forms possible, and ground conditions
|
- Major Feature: Completed maneuvering implementation with Android app
- [Android I/O:] Sensor obstacle LIDAR information has been updated on the app
- [Android I/O:] Dynamic update of Car's current location and intermittent checkpoints implemented.
- [Android I/O:] Health information from BLE Controller, namely GPS lock status, and motor speed has been updated on the Dashboard of the app.
- [Android I/O:] Completed BT Auto connect implementation and re-connection on disconnection.
|
Complete.
|
| 9
|
11/28/2017
|
- Major Feature: Full feature integration test
- Execute the test plan created above [Planned for 11/14] (check Testing documentation in Wiki)
- Execute the test plan created above [Planned for 11/14]; Phase 1: Test all identified cases for ground-conditions (grass, inclines, etc)
- Execute the test plan created above [Planned for 11/14]; Phase 2: Test all identified cases for GPS routes and obstacle forms
|
- Major Feature: Full feature integration test
- Integration testing with all controllers and Android App to select routes and send checkpoints from App to Ble.
|
Complete.
|
| 10
|
12/5/2017
|
- Major Feature: Full feature integration test
- Execute the test plan created above [Planned for 11/14]; Phase 3: Test all identified cases for speed levels and on-board I/O validation
- Execute the test plan created above [Planned for 11/14]; Phase 4: Test all identified cases for [Android I/O] validation
|
- Major Feature: Full feature integration test
- Integration testing with Android App with Debug view/Dash board with sensor and GPS data
|
Complete
|
| 11
|
12/12/2017
|
- Major Feature: Full feature integration test
- Execute the test plan created above [Planned for 11/14]; Phase 5: Test all identified cases for desired Turbo mode(s)
- Update Wiki Complete Report
|
- Major Feature: Full feature integration test
|
On Track
|
Parts List & Cost
The Project bill of materials is as listed in the table below.
CAN Communication
System Nodes : MASTER , MOTOR , BLE , SENSOR , GEO
| SNo.
|
Message ID
|
Message from Source Node
|
Receivers
|
| Master Controller Message
|
| 1
|
2
|
System Start command to start motor
|
Motor
|
| 2
|
17
|
Target Speed-Steer Signal to Motor
|
Motor
|
| 3
|
194
|
Telemetry Message to Display it on Android
|
BLE
|
| Sensor Controller Message
|
| 4
|
3
|
Lidar Detections of obstacles in 360 degree grouped as sectors
|
Master,BLE
|
| 5
|
36
|
Heartbeat
|
Master
|
| Geo Controller Message
|
| 4
|
195
|
Compass, Destination Reached flag, Checkpoint id signals
|
Master,BLE
|
| 5
|
4
|
Turning Angle
|
Master,BLE
|
| 5
|
4
|
Heartbeat
|
Master
|
| Bluetooth Bridge Controller Message
|
| 4
|
38
|
Heartbeat
|
Master
|
| 5
|
213
|
Checkpoint Count from AndroidApp
|
Geo
|
| 5
|
214
|
Checkpoints(Lat,Long) from Android App
|
Geo
|
DBC File
https://gitlab.com/optimus_prime/optimus/blob/master/_can_dbc/243.dbc
Android and Communication Bridge
Group Members
Design & Implementation
Pin Configuration:
Hardware Design
Software Design and Implementation
Android App
BLE Controller
Testing & Technical Challenges
Geographical Controller
Group Members
Hardware Design
GPS and Compass Module:
We are using DJI’s NAZA GPS/COMPASS to get the GPS coordinates and Heading angle. The diagram of the module is as follows:
Message Structure:
The 0x10 message contains GPS data. The message structure is as follows:
55 AA 10 3A DT DT DT DT LO LO LO LO LA LA LA LA
The payload is XORed with a mask that changes over time.
Values in the message are stored in little endian.
HEADER
BYTE 1-2: message header - always 55 AA
BYTE 3: message id (0x10 for GPS message)
BYTE 4: length of the payload (0x3A or 58 decimal for 0x10 message)
PAYLOAD
BYTE 5-8 (DT): date and time
BYTE 9-12 (LO): longitude (x10^7, degree decimal)
BYTE 13-16 (LA): latitude (x10^7, degree decimal)
CHECKSUM
BYTE 63-64 (CS): checksum
XOR mask
All bytes of the payload except 53rd (NS), 54th, 61st (SN LSB) and 62nd (SN MSB) are XORed with a mask. Mask is calculated based on the value of byte 53rd (NS) and 61st (SN LSB).
Pin Configuration:
The Pin Configuration is as follows:
Software Design
Algorithm:
Distance calculation:
We are using the ‘haversine’ formula to calculate the great-circle distance between two points – that is, the shortest distance over the earth’s surface
Haversine formula:
a = sin²(Δφ/2) + cos φ1 ⋅ cos φ2 ⋅ sin²(Δλ/2)
c = 2 ⋅ atan2( √a, √(1−a) )
d = R ⋅ c
where φ is latitude, λ is longitude, R is earth’s radius (mean radius = 6,371km)
Bearing Angle calculation:
Formula:
θ = atan2( sin Δλ ⋅ cos φ2 , cos φ1 ⋅ sin φ2 − sin φ1 ⋅ cos φ2 ⋅ cos Δλ )
where φ1,λ1 is the start point, φ2,λ2 the end point (Δλ is the difference in longitude)
Since atan2 returns values in the range –π to +π (that is, -180° to +180°), to normalize the result to a compass bearing (in the range 0° to 360°), negative values are transformed into the range 180° to 360°) by converting to degrees first and then using (θ+360) % 360, where % is (floating point) modulo.
DBC Messages:
Messages sent from GEO module:
BO_ 4 GEO_TURNING_ANGLE: 2 GEO
SG_ GEO_TURNING_ANGLE_degree : 0|9@1- (1,0) [-180|180] "" MASTER,BLE
BO_ 37 GEO_HEARTBEAT: 1 GEO
SG_ GEO_HEARTBEAT_signal : 0|8@1+ (1,0) [0|255] "" MASTER
BO_ 195 GEO_TELECOMPASS: 6 GEO
SG_ GEO_TELECOMPASS_compass : 0|12@1+ (0.1,0) [0|360.0] "" MASTER,BLE
SG_ GEO_TELECOMPASS_bearing_angle : 12|12@1+ (0.1,0) [0|360.0] "" MASTER,BLE
SG_ GEO_TELECOMPASS_distance : 24|12@1+ (0.1,0) [0|0] "" MASTER,BLE
SG_ GEO_TELECOMPASS_destination_reached : 36|1@1+ (1,0) [0|1] "" MASTER,BLE
SG_ GEO_TELECOMPASS_checkpoint_id : 37|8@1+ (1,0) [0|0] "" MASTER,BLE,SENSOR
BO_ 196 GEO_TELEMETRY_LOCK: 1 GEO
SG_ GEO_TELEMETRY_lock : 0|8@1+ (1,0) [0|0] "" MASTER,SENSOR,BLE
BO_ 214 GEO_TELEMETRY: 8 GEO
SG_ GEO_TELEMETRY_LONG : 0|32@1- (0.000001,0) [0|0] "" MASTER
SG_ GEO_TELEMETRY_LAT : 32|32@1- (0.000001,0) [0|0] "" MASTER
Messages received by GEO module:
BO_ 212 BLE_GPS_DATA: 8 BLE
SG_ BLE_GPS_long : 0|32@1- (0.000001,0) [0|0] "" GEO
SG_ BLE_GPS_lat : 32|32@1- (0.000001,0) [0|0] "" GEO
BO_ 213 BLE_GPS_DATA_CNT: 1 BLE
SG_ BLE_GPS_COUNT : 0|8@1+ (1,0) [0|0] "" GEO,SENSOR
Implementation
Periodic callback function description:
1 Hz Function:
a. Check CAN bus
b. Send Heartbeat to Master module
c. Send GPS lock to Master and Sensor modules
100 Hz Function:
a. Get GPS coordinates
b. Get Heading angle
c. Get Checkpoints count
d. Calculate Bearing angle
e. Calculate Turning angle
f. Calculate Distance remaining
g. Send Heading angle
h. Send Bearing angle
i. Send Turning angle
j. Send Distance remaining
k. Check Destination reached
Testing & Technical Challenges
Sensor and I/O
Group Members
Design & Implementation
Hardware Design
Hardware Interface
Software Design and Implementation
Design & Implementation
Hardware Interface
Software Design
Testing & Technical Challenges
Motor Controller
Group Members
Design & Implementation
Hardware Design
Software Design
Implementation
Testing & Technical Challenges
Master Controller
Group Members
Introduction and Responsibilities
Hardware Design
Software Design
Software Implementation
Common Technical Challenges
Conclusion
Project Videos
Project Source Code
References
Acknowledgement
