F16: Piano Glove
Contents
- 1 Grading Criteria
- 2 Project Title
- 3 Abstract
- 4 Objectives & Introduction
- 5 Schedule Overview
- 6 Parts List & Cost
- 7 Hardware Design & Interface
- 8 Software Design & Implementation
- 9 Integration Testing, Results, & Technical Challenges
- 10 Conclusion
- 11 References
Grading Criteria
- How well is Software & Hardware Design described?
- How well can this report be used to reproduce this project?
- Code Quality
- Overall Report Quality:
- Software Block Diagrams
- Hardware Block Diagrams
- Schematic Quality
- Quality of technical challenges and solutions adopted.
Project Title
OVS: Piano Glove
Abstract
The Piano Glove is a device that is capable of synthesizing the notes of a Baby Grand Piano.
Objectives & Introduction
Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.
Team Members & Responsibilities
- Full System & PCB Design
- Digital Signal Processing in MATLAB
- Device Driver Implementation
- System Integration, Verification, and Validation Testing
- Algorithm Development
- Device Driver Implementation
- System Integration, Verification, and Validation Testing
Schedule Overview
Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.
Week # | Start Date | End Date | Team Task Description | Status | Actual End Date |
---|---|---|---|---|---|
1 | 10/14/16 | 10/21/16 | Research Design Approach and Assign Tasks | Complete | 10/21/16 |
2 | 10/21/16 | 10/28/16 | Set up Version Control and Research Parts | Complete | 10/28/16 |
3 | 10/28/16 | 11/4/16 | Discuss MCU Responsibilities and Communication | Complete | 11/4/16 |
4 | 11/4/16 | 11/11/16 | Purchase Parts and Begin Prototyping | In Progress | 11/11/16 |
5 | 11/11/16 | 11/18/16 | Status Update: Demo First Round of Prototyping | N/A | |
6 | 11/18/16 | 11/25/16 | Interface Modules and Perform System Design Verification/Validation Testing | N/A | |
7 | 11/25/16 | 12/02/16 | Continue Validation and Optimize System | N/A | |
8 | 12/02/16 | 12/20/16 | Finalize Design and Prepare for Demo | N/A |
|
Parts List & Cost
Give a simple list of the cost of your project broken down by components. Do not write long stories here.
Item # | Part Description | Vendor | QTY | Cost (USD) |
---|---|---|---|---|
1 | SJSUOne Board | Preet | 1 | $80 |
2 | Flex Sensor | Mouser | 10 | $6.45 |
3 | MCP4822-E/P DAC | Mouser | 10 | $3.06 |
4 | MCP6242-E/P OPAMP | Mouser | 10 | $0.36 |
5 | Gloves | Nike | 1 | $12.99 |
6 | Misc Parts (Wires, Resistors, etc) | Personal | N/A | Free |
Software Used
Hardware Design & Interface
The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.
Hardware Schedule
Discuss your hardware design here. Show detailed schematics, and the interface here.
Week # | Start Date | End Date | Description | Status | Actual End Date | Comments |
---|---|---|---|---|---|---|
1 | 10/21/16 | 11/4/16 | Research Design Implementation and Brainstorm PCB Schematic Layout Determine and Purchase Parts |
Completed | 11/4/16 | |
2 | 11/4/16 | 11/11/16 | Design and Interface Schmitt Trigger Circutry w/SJSUOne Board Create PCB Schematic |
Completed | 11/11/16 | PCB design is not complete, we are not sure that it is necessary. |
3 | 11/11/16 | 11/18/16 | Sew Flex Sensors onto Gloves and Interface w/Development Board Send PCB out for fabrication Status Update: Demo First Round of Prototyping |
In Progress | Sewing the sensors onto the gloves was tedious. The sensors are very fragile, so they had to be handled with caution. | |
4 | 11/18/16 | 11/25/16 | Interface Modules and Perform System Design Verification/Validation Testing | N/A | ||
5 | 11/25/16 | 12/02/16 | Continue Validation and Optimize System | N/A | ||
6 | 12/02/16 | 12/20/16 | Finalize Design and Prepare for Demo | N/A |
Hardware Development
System Block Diagram
The following diagram is a high-level overview of our system. It is depicts the general structure of our design. In addition to that, it also demonstrates a generalization of the major system components that were used as well as their relationship among each other.
Flex Sensors
Schmitt and Trigger
The Schmitt and Trigger circuit is used to convert the Analog Output of the Flex Sensors into a Digital Signal. This Analog to Digital Conversion (ADC) is done so that the SJSUOne MCU can interpret the input signal using a GPIO port.
- Design Choice: we decided to create our own ADC circuit because of the limited availability on the SJSUOne board. There are simply not enough ADC pins to perform our task, as we would need 10 ADC pins.
SJSUOne Board
General Purpose Input/Output (GPIO)
Digital to Analog Converter (DAC)
Design Choice Trade-Off: Due to time and money constraints, we used the on-board DAC which was 10-Bits. Since it is 10-Bits, we are only able to get 1K distinct values, as opposed to 4K with a 12-Bit DAC. In order to use a 12-Bit DAC, we would have had to purchase an additional part and interface it with the MCU. Thus, we chose ultimately choose to save time and money over getting a more precise result.
Intel Compute Stick
PCB Design & Schematic
Datasheets
System Interface
In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.
Software Design & Implementation
Software Schedule
Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.
Week # | Start Date | End Date | Description | Status | Actual End Date |
---|---|---|---|---|---|
1 | 10/21/16 | 10/28/16 | Research the following: Algorithm Design/Implementation and Digital Signal Processing in MATLAB |
Complete | 10/28/16 |
2 | 10/28/16 | 11/11/16 | Develop Algorithm and Device Drivers as well as Incorporating RTOS | In Progress | |
3 | 11/11/16 | 11/18/16 | Status Update: Demo First Round of Prototyping | In Progress | |
4 | 11/18/16 | 11/25/16 | Implement Code w/Integrated Unit and Begin Debugging As Necessary | N/A | |
5 | 11/25/16 | 12/02/16 | Continue System Integration Testing for Validation and Optimization | N/A | |
6 | 12/02/16 | 12/20/16 | Finalize Design and Prepare for Demo | N/A |
|
Audio Algorithm Development
Algorithm Flowchart
Karplus Strong
Visualization Development
Communication Protocols & Device Drivers
GPIO
Bluetooth
Implementation
This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.
Integration Testing, Results, & Technical Challenges
Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.
Include sub-sections that list out a problem and solution, such as:
Hardware
My Issue #1
- Initially we had ordered the wrong parts. Due to time constraints, we rushed selecting parts and were not careful on selecting the components that had the right packaging. Therefore, we ended up purchasing MSOPs (Mini-Small-Outlined-Package) instead of PDIPs (Plastic Dual Inlined Package). Using MSOPs would not work for us because the IC was simply too small to work with. It would not be able to fit on our breadboard for prototyping purposes.
For more information on IC Packaging and Dimensions, please refer to this link: IC Package Dimensions
Validation
Oscilloscope Readings
My Issue #1
My Issue #2
Discuss the issue and resolution.
Software
Digital Signal Processing in MATLAB
DSP Simulations
My Issue #1
My Issue #2
Discuss the issue and resolution.
Full System Integration
My Issue #1
Conclusion
Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?
Project Video
Upload a video of your project and post the link here.
Project Source Code
References
Acknowledgement
Any acknowledgement that you may wish to provide can be included here.
References Used
List any references used in project.
Appendix
You can list the references you used.