S19: CANT Bus

From Embedded Systems Learning Academy
Revision as of 13:06, 23 May 2019 by Proj user15 (talk | contribs) (Modules)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
  • Hardware Block Diagrams
    • Schematic Quality
    • Quality of technical challenges and solutions adopted.

[C]ompile [A]nother [N]on-[T]rivial Bus

Abstract

Design and implement an autonomous car to navigate to a destined location chosen by the user using a phone application. The user will set gps coordinates via an Android application while the current location is processed. The RC car should be able to use these coordinates to navigate itself to the destined location avoiding obstacles and providing useful data on the way. Several objectives need to be completed in order for the RC car to function properly: integrate proximity sensors, gps, compass, lcd screen, motor driver board, esp32 communication, hall sensor, and overall integration in order for the RC car to be able to determine where it is, the speed it's going, and the environment around it to successfully navigate to the final destination.

Introduction

The purpose of this project was to convert a RC car into a self driving vehicle that can navigate itself to a destination sent via an Android mobile app. To achieve this, the project was divided into 7 modules: Avoidance, Motor, Master Driver, Localize, Comms, and Android Application. The Avoidance module contains 8 IR sensors that allow the car to see the world around it. This module finds objects and measures the distance between it and the object. Motor controls a brushed motor which drives the car at various speeds and a servo to turn the car. In addition, Motor also contains a hall effect sensor that keeps track of the cars speed. Localize tells the car where it is in relation to where it needs to go. It contains a GPS and Compass to provide current coordinates and heading. Comms houses the wireless device that talks to the the mobile app as well as an LCD display to show various car data such as speed and destination. The mobile app is where the user can enter GPS coordinates as a destination point, or alter the current destination with a way-point. Lastly, the Driver receives the data from all modules and decides how the car shall react. In order to complete these modules basic knowledge of I2C, UART, SPI, and CAN bus protocols, gpio control, PWM control, phone application development, and pathing algorithms was required. While each peripheral in the modules used their own form of communication, each of the modules was connected using the CAN bus protocol.

Team Members & Responsibilities

  • Kevin Chan
    • IR sensors (Proximity), Compass (Localize), GPS (Localize), Distance Vector (Localize), Code Review
  • Khrysta Finch
    • Chassis, Driver (Driver), LCD display (Comms), Schematic, Telemetry (Comms)
  • Andrew Javier
    • Hall Sensor (Motor), Wireless communications via esp32(Comms), GPS (Localize), Chassis
  • Aaron Lee
    • GPS (Localize), Pathing Algorithm (Comms)
  • Jonathan Rojas
    • Motor (Motor), Servo (Motor), Motor driver board (Motor), hall sensor (Motor), Cable Management, Chassis
  • Vijay Vanapalli
    • GPS (Localize), Wireless communications via esp32(Comms), Mobile app (Comms)
  • Nelson Wong
    • Team Leader, Driver (Driver), Telemetry (Comms), PCB/Schematic, Chassis, Mobile App (Comms), Power, Code Review


Source Code

Gitlab Project Link


Modules

  • Android Application
    • Vijay Vanapalli
  • Testing Team
    • Kevin Chan
    • Nelson Wong


Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Week# Start Date End Date Task Description Status Completion Date
1 3/4 3/10
  • Strategize approach
  • Determine tasks
  • Assign tasks
  • Draft architecture
Complete
2 3/11 3/17
  • Finalize architecture
  • Order parts
  • Begin electrical schematic and PCB design
3 3/18 3/24
  • Finalize electrical schematic and PCB design
  • Begin code design per subsystem (must include UT!)
4 3/25 3/31
  • Continued code design and editing
  • Begin app dev
  • Order PCB
5 4/1 4/7
  • Hardware assembly
  • Code review
6 4/8 4/14
  • App dev complete
  • Continue HW assembly
  • Begin outdoor testing
7 4/15 4/21
  • Review, Revise, Retest
8 4/22 4/28
  • Review, Revise, Retest
  • Code lock at end of the week
9 4/29 5/5
  • To be determined
10 5/6 5/12
  • To be determined

Parts List & Cost

Item# Part Desciption Vendor Qty Cost
1 RC Car Traxxas 1 $250.00
2 CAN Transceivers MCP2551-I/P Microchip [1] 8 Free Samples

Printed Circuit Board

We used the online tool Upverter to create our schematic and design the final PCB board. Both schematic and board can be found on Upverter using the link below.

PCB and Schematic

CAN Communication

CAN BUS Messages

The DBC file that was used to generate our CAN messages can be found below. Each message has a priority ID assigned to it that is used by the CAN protocol to see which device to listen to first in cases of bus arbitration; the lower the ID number the higher priority it has. In our case, the message with the highest priority at 10 is KILL_MOTOR. Since we are using LiPO (Lithium Polymer) batteries, the desire to disconnect all power for the battery depleted was high on the list. Should the car be driving at that time, the KILL_MOTOR_cmd shuts off the motor immediately, allowing us to catch up to the car and swap out batteries. The KILL_MOTOR_REMOTE message follows the KILL_MOTOR message in priority. This is simply a redundancy we built in to have the message delivered to the mobile app and notifying us that the battery is low.

The priority decreases from there with HEARTBEAT from the Driver being the next highest. Since the Driver doesn't send many messages and it's there to collect data from all the other modules, it needs to let the others know it's still available. MOTOR_CMD follows as we wanted the car to move as quickly as possible, which leads to AVOIDANCE_LIDAR as the next highest. Knowing when we were in close proximity to an object is key to making sure we don't run into it. Note that while this message has "LIDAR" as part of the name, this is legacy nomenclature from when we initially had LIDAR for the car. They are now IR sensors.

GPS, Compass, and Speed were assigned the lowest priorities. While knowing where we are in relation to where we are going is important, it was less demanding that knowing if we are about to hit something or if the battery was depleted. Overall, this choice in priority has served well in providing a functional autonomous car.



Hardware Design

Each of the modules are connected to a CAN transceiver via transmit and receive lines. The transceivers themselves are connected together through their CAN high and low pins (CANH/CANL) with each of those lines terminating with a 120 ohm resistor.

Figure X: CAN bus architecture design

CAN DBC File

BS_:
BU_: COMMS DRIVER LOCALIZE MOTOR AVOIDANCE

BO_ 10 KILL_MOTOR: 1 DRIVER
 SG_ KILL_MOTOR_cmd : 0|8@1+ (1,0) [0|0] "" MOTOR,COMMS
 
BO_ 11 KILL_MOTOR_REMOTE: 1 COMMS
 SG_ KILL_MOTOR_cmd : 0|8@1+ (1,0) [0|0] "" DRIVER 
 
BO_ 100 DRIVER_HEARTBEAT: 1 DRIVER
 SG_ DRIVER_HEARTBEAT_cmd : 0|8@1+ (1,0) [0|0] "" LOCALIZE,COMMS,AVOIDANCE,MOTOR 
 
BO_ 101 MOTOR_CMD: 2 DRIVER
 SG_ MOTOR_CMD_steer : 0|3@1+ (1,-1) [-1|1] "degrees" MOTOR
 SG_ MOTOR_CMD_drive : 8|4@1+ (1,-2) [-2|5] "" MOTOR
 
BO_ 102 DRIVER_STATUS: 1 DRIVER
 SG_ DRIVER_STATUS_enum : 0|3@1+ (1,0) [0|0] "" COMMS
 
BO_ 200 AVOIDANCE_LIDAR: 8 AVOIDANCE
 SG_ LIDAR_f_right : 0|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_f_m_right : 8|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_f_middle : 16|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_f_m_l : 24|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_f_left : 32|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_b_right : 40|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_b_middle : 48|8@1+ (1,0) [0|0] "cm" DRIVER
 SG_ LIDAR_b_left : 56|8@1+ (1,0) [0|0] "cm" DRIVER

BO_ 201 DESIRED_VECTOR: 8 LOCALIZE
 SG_ DESIRED_HEADING : 0|32@1+ (0.1,0) [0|360.0] "degrees" DRIVER,COMMS
 SG_ DESIRED_DISTANCE : 32|32@1+ (0.00001,0) [0|0] "km" DRIVER,COMMS

BO_ 300 LOCALIZE_GPS: 8 LOCALIZE
 SG_ GPS_STATUS : 0|8@1+ (1,0) [0|0] "" DRIVER,COMMS
 SG_ GPS_TX_LATITUDE : 8|24@1+ (0.000001,37.000000) [37.000000|38.000000] "degrees" DRIVER,COMMS
 SG_ GPS_TX_LONGITUDE : 32|32@1- (0.000001,-122.000000) [-122.000000|-121.000000] "degrees" DRIVER,COMMS

BO_ 301 LOCALIZE_IMU: 8 LOCALIZE
 SG_ IMU_STATUS : 0|8@1+ (1,0) [0|0] "" DRIVER,COMMS
 SG_ IMU_COMPASS : 8|12@1+ (0.1,0) [0|360.0] "degrees" DRIVER,COMMS
 
BO_ 302 SPEED: 8 LOCALIZE
 SG_ SPEED_kph : 0|16@1- (0.001,0) [-5|10] "kph" COMMS,DRIVER

BO_ 303 LOCALIZE_IMU_DEBUG: 8 LOCALIZE
 SG_ IMU_COMPASS_X : 0|10@1- (1,0) [-200|200] "" DBG
 SG_ IMU_COMPASS_Y : 10|10@1- (1,0) [-200|200] "" DBG

BO_ 400 MOTOR_STATUS: 1 MOTOR
 SG_ MOTOR_STATUS_data : 0|8@1+ (1,0) [0|0] "" COMMS,DRIVER
 
BO_ 500 SET_WAYPOINT: 8 COMMS
 SG_ SET_WAYPOINT_LAT : 0|24@1+ (0.000001,37.331610) [37.331610|37.340132] "degrees" LOCALIZE,DRIVER
 SG_ SET_WAYPOINT_LONG : 24|24@1- (0.000001,-121.886025) [-121.886025|-121.876412] "degrees" LOCALIZE,DRIVER

BO_ 501 SET_STATUS: 1 COMMS
 SG_ SET_STATUS_enum : 0|2@1+ (1,0) [0|0] "" DRIVER

BO_ 700 DRIVER_DEBUG: 8 DRIVER
 SG_ VEL_ARR : 0|32@1+ (1,0) [0|0] "" AVOIDANCE

BO_ 701 AVOIDANCE_DEBUG: 8 AVOIDANCE
 SG_ AVOIDANCE_COUNT : 0|32@1+ (1,0) [0|0] "" DRIVER

BO_ 702 MOTOR_DEBUG: 4 MOTOR
 SG_ MOTOR_SPEED_DBG : 0|32@1+ (0.0001,0) [0|0] "ms" DRIVER

BO_ 704 TACHOMETER_DEBUG: 8 LOCALIZE
 SG_ TACHOMETER_DBG : 0|16@1- (0.001,0) [-5|10] "kph" COMMS,DRIVER

CM_ BU_ DRIVER "The driver controller driving the car";
CM_ BU_ MOTOR "The motor controller of the car";
CM_ BU_ LOCALIZE "The localization controller of the car";
CM_ BU_ AVOIDANCE "The collision avoidance controller of the car";
CM_ BU_ COMMS "The wireless comms and telemetry controller of the car";
CM_ BO_ 100 "Sync message used to synchronize the controllers";
CM_ BO_ 501 "0: stop, 1: ready, 2: navigate, 3: skip/next"
BA_DEF_ "BusType" STRING ;
BA_DEF_ BO_ "GenMsgCycleTime" INT 0 0;
BA_DEF_ SG_ "FieldType" STRING ;
BA_DEF_DEF_ "BusType" "CAN";
BA_DEF_DEF_ "FieldType" "";
BA_DEF_DEF_ "GenMsgCycleTime" 0;
BA_ "GenMsgCycleTime" BO_ 500 100;
BA_ "GenMsgCycleTime" BO_ 100 1000;
BA_ "GenMsgCycleTime" BO_ 101 100;
BA_ "GenMsgCycleTime" BO_ 400 100;
BA_ "GenMsgCycleTime" BO_ 200 100;
BA_ "FieldType" SG_ 102 DRIVER_STATUS_enum "DRIVER_STATUS_enum";
BA_ "FieldType" SG_ 103 SET_STATUS_enum "SET_STATUS_enum"; 
BA_ "FieldType" SG_ 500 DBC_TEST1_enum "DBC_TEST1_enum";
BA_ "FieldType" SG_ 100 DRIVER_HEARTBEAT_cmd "DRIVER_HEARTBEAT_cmd";
VAL_ 102 DRIVER_STATUS_enum 7 "STOP" 6 "FWD_R" 5 "REV_R" 4 "REV_M" 3 "REV_L" 2 "FWD_L" 1 "FWD_M" 0 "IDLE" ;
VAL_ 103 SET_STATUS_enum 1 "GO" 0 "STOP" ;
VAL_ 500 DBC_TEST1_enum 2 "DBC_TEST1_enum_val_two" 1 "DBC_TEST1_enum_val_one" ;
VAL_ 100 DRIVER_HEARTBEAT_cmd 2 "DRIVER_HEARTBEAT_cmd_REBOOT" 1 "DRIVER_HEARTBEAT_cmd_SYNC" 0 "DRIVER_HEARTBEAT_cmd_NOOP" ;

Proximity ECU

<Picture and link to Gitlab>

The Proximity ECU was also known as the Avoidance module and can be found on GitLab here. It's sole purpose is to monitor the environment around the car and take measurements of objects that break the threshold.

Hardware Design

Avoidance contains eight VL53L0X infrared sensors for obstacle detection that utilizes the I2C interface. The sensors measure a distance in centimeters with a maximum range of 2 meters with 1 millimeter resolution. The VL53L0X sensor used in the car was purchased pre-attached to a breakout board where the voltage was stepped down from 3.3V to 2.8V. The XSHUT pin on the sensor acts as an enable where they were wired to GPIO pins on the SJOne board. For the car, there were a total of 8 sensors used: 5 in the front, 3 in the back. The sensors come preassigned to an address of 0x52 but can be reassigned to a different address. The table for sensor address assignment and GPIO are seen below.

Sensor Position GPIO pin Slave Address
Front Right P2_2 0x54
Front Middle Right P0_30 0x61
Front Middle P2_1 0x56
Front Middle Left P0_29 0x63
Front Left P2_0 0x58
Back Right P2_5 0x5A
Back Middle P2_4 0x5C
Back Left P2_3 0x5E
Default none 0x52

Power for the sensors came from the car power supply regulated for 3.3V instead of from the SJOne board. The problem and solution of assignment of the I2C address can be seen below in the software design. The block diagram for this module can be found below. Note that for brevity, not all 8 proximity sensors are shown. Each sensor is connected in the same manner each with its own dedicated GPIO pin.


Figure X: Proximity IR sensors

Software Design

<List the code modules that are being called periodically.>

For the software design, a C++ library was ported over from Pololu along with configuration of the library to work with the SJOne Board. A C wrapper was written to allow it to be unit tested and included in our periodic_callbacks.c file. There were difficulties with having a singleton object for 8 sensors that created conflict. This was resolved by having a table of addresses, that the singleton object would select and reassign its address with to sweep through the sensor addresses. The configuration of the reassignment of addresses also took careful consideration.

The initialization function for these sensors followed the flowchart below of how to reassign the addresses of each sensor even when they all start with the initialized with the same address. The process would first enable the first sensor with XSHUT using the GPIO pin, the singleton object would set its address to the default address of 0x52. The function would then initialize it depending on the which GPIO function was enable to the addresses seen above in the table and write to the device register to change its slave address. After initializing was completed for one sensor, the sensor would stay enabled, but the singleton object would be reset back to 0x52 to set the next sensor.

Figure X: Proximity IR Init Flowchart

To collect and store data from each sensor, a data structure was created to be placed in a CAN message. A function was created where it would again sweep the address space of the address table, and store the data to its respective location in the data structure. This occurs every 20 Hz, where a CAN message is broadcasted on the bus for DRIVER to use.

Technical Challenges

The only issues with the proximity sensors came from using a library provided by Pololu that used a singleton object. To address this issue, a table of addresses was created where the singleton object would sweep the table of addresses to retrieve data from each sensor. The singleton object would reassign its own address from the table to access each sensor individually. The process described in the software design was also used for retrieving data from each sensor.



Motor ECU

Figure X: Architecture of Motor Controller

Hardware Design

Software Design

Motor

Periodic Init

  • Initializes CAN, servo PWM (50Hz), motor driver board PWM (100Hz), interrupt for hall sensor, and speed calibration

1Hz Task

  • Used to check the state of CAN and reset.

10Hz Task

  • Receive CAN message for Motor Control
  • Send Motor Status
  • Send Motor Speed

Technical Challenges

  • Motor and Servo Frequencies
  • Hall Sensor Speed Determination

Motor and Servo Frequencies

<Problem Summary>

  • Single frequency for PWM on SJone board

Using PWM on the SJOne board only allows for one PWM frequency on all the PWM pins. For Motor, we required two different frequencies (motor (100Hz) and servo (50Hz)). We solved this by using a motor driver board using i2c to create a second PWM frequency.

  • Fluctuating PWM Frequency

The PWM for MOTOR varied by a few Hz depending on the environment causing the duty cycle to control the motor to change. We set the frequency to be 100Hz, but varied between 98.7Hz. This caused the dutycycle to change from 70% to 80% to initiate the motor.


<Problem Resolution>

  • Single frequency for PWM on SJone board

We solved this by using a motor driver board using i2c to create a second PWM frequency.

  • Fluctuating PWM Frequency

In order to be able to deal with any situation and environment the RC car will be in we created a function to manually calibrate the first speed by increasing the dutycycle by 1% using push buttons and automatically incrementing the higher speeds with it.

Hall Sensor Speed Determination

<Problem Summary>

  • Creating a secure mount with enough magnets

Using PWM on the SJOne board only allows for one PWM frequency on all the PWM pins. For Motor, we required two different frequencies (motor (100Hz) and servo (50Hz)). We solved this by using a motor driver board using i2c to create a second PWM frequency.

  • Fluctuating PWM Frequency

The PWM for MOTOR varied by a few Hz depending on the environment causing the duty cycle to control the motor to change. We set the frequency to be 100Hz, but varied between 98.7Hz. This caused the dutycycle to change from 70% to 80% to initiate the motor.


<Problem Resolution>

  • Single frequency for PWM on SJone board

We solved this by using a motor driver board using i2c to create a second PWM frequency.

  • Fluctuating PWM Frequency

In order to be able to deal with any situation and environment, the RC car will be in we created a function to manually calibrate the first speed by increasing the dutycycle by 1% using push buttons and automatically incrementing the higher speeds with it.




Localize ECU

Figure X: Geographic Controller

Hardware Design

LSM303

The LSM303 was selected as the compass for the final product. The LSM303 is a digital compass that contains an acceleration sensor and temperature sensor onboard. It uses the I2C communication protocol and can be power via a 5V or 3.3V power source. For this sensor, the SJOne board directly powered the compass. The clock rate for the slave clock was set to 100 KHz. The compass requires calibration which will be described in the both the software and technical challenges.

Figure X: LSM303 Block Diagram

NEO-6M GPS

Figure X: Neo-6M GPS Module

The Neo-6M GPS module was the device used to supply the SJOne board with positioning information. It communicates using the UART protocol and sets information at a baud rate of 9600. When powered, the module automatically sends various NMEA sentences at a rate of 1 Hz. Its only connection to the SJOne board is through the Rx pin through the Neo-6M Tx pin. The module itself has two main components: the Neo-6M module and the receiver. For optimal results, the receiver and module were mounted separately and above all other components with the white side facing up and the metallic side of the receiver facing down. While results were not perfect, it provided the most accurate and consistent results.

Software Design

LSM303

For the LSM303, the compass required an initialization function to set all the registers. The slave address for writing to the LSM303 is 0x3D and to read from the registers is 0x3C. The data for the compass can be read from 6 8-bit registers, where X Y and Z axis are divided into high and low registers. The data is represented in two’s-complement where the conversion needed to be done after merging the two bytes together. As per the datasheet, the X axis is registers 3 and 4, where register 3 is the high byte and 4. The same goes for the Z axis which is registers 5 and 6, and Y is registers 7 and 8. After the raw coordinates are obtained, the calibration goes into effect.

LSM303 Slave Address Operation
0x3D Write
0x3C Read
Figure X: Compass Heading Calculation Flow

To calibrate the compass, the X and Y points were plotted while negating the Z axis. The Z axis was negated because the calibration of the compass requires that the compass be perfectly level. A sample of points were collected, and the plot can be seen below.

Figure X: LSM303 raw data, no shifting, no calibration

To calibrate the compass, offsets were added such that the circle is centered at 0,0. The calibration was then added, and it looks like the plot below.

Figure X: LSM303 X shifted down 50, Y shifted down 50

An additional feature that needed to be added was closing the gaps created from having the compass close to the car. Shifting was needed to close the circle when there were gaps in the calibration caused from the electronics of the car.

Figure X: LSM303 data on car with gaps caused by electronics

After the points have been calibrated, an angle was formed from the point in relation to 0,0. The points go counter clockwise it goes in the order of North - 0, East - 90, South - 180, West - 270. The X and Y points were outputted to the CAN bus as a debug message and the compass direction was used for pathing.

Figure X: Compass direction based on points

NEO-6M GPS

There are three main stages to collecting data from the Neo-6M GPS module. The first is to store the raw data into a string from the UART receive buffer. The second step is the verify the validity of the message and the string and store the different parts of the message into a struct if the message is valid. The final step is to verify the coordinates stored in the struct.

Message collection from the Neo-6M is handled through the UART library on the SJOne board. Two of the functions were used:

  • is_Queue_Not_Empty() which returns the value of getRxQueueSize()
  • gets() which stores the messages into a string and is ended through a timeout, reaching the final character of the string, or a new line character

Due to messages arriving once per second, these two functions were necessary. The is_Queue_Not_Empty() function only allows reading if a message is ready on the queue. This will prevent a message from being cut off due to timeout. Since every message is appended with a new line character, gets() will store the message into the buffer without storing parts of a new message.

For the second part of the GPS data collection, the Tiny GPS++ library was used. This provided us resources to parse and store the data from the various NMEA libraries. Furthermore, the library contains a TinyGPSCustom class which allows us to focus only on the $GPRMC messages. If a message was stored into a buffer, then this second part of GPS data collection occurred. The first step is to run the Tiny GPS++ function encode(char c). This function passes in a char and stores it in a substring. Each substring is created after receiving a $ and is eventually checked once the * character was received. If the checksum passes, then the commit() function is called which stores all of the data in the string into a struct. The following shows an example of the $GPRMC message.

$GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4,230394,003.1,W*6A

The fields of GPRMC are message time, current time in UTC, validity of GPS, latitude in degree-minute-second, north/south, longitude in degree-minute-sentence, east/west, speed over ground in knots, track angle, current date, magnetic variation, and checksum. Of these fields, the GPS validity, latitude, longitude, and checksum were used. When latitude and longitude are stored in the struct, they are converted into a decimal form from degree-minute-second.

The final part of the GPS data collection is to validate the latitude and longitude values obtained from the Tiny GPS++ library. Due to nuances with the string, it is possible to obtain values that are inconsistent with the current location. It is also possible to get a latitude and longitude of 0 if the validity of GPS field of the $GPRMC message had a V for void. The check was performed by the valid_coordinates(float latitude, float longitude) function and would only return true if the latitude was between 37 and 38 and if the longitude was between -122 and -121. Should these conditions meet, the coordinates were updated and the value is sent to the CAN bus. If they aren't meet, the old values remain the same until a validity check changes them.

Figure X: GPS Data Collection Flow

Technical Challenges

  • Calibration of LSM303
    • The problem with the LSM303 and all digital compasses, is there is a lot of interference with magnetic fields in buildings that requires calibration for different environments. In addition, compasses do not come pre-calibrated as the strength of the North pole varies depending on location. To resolve this issue, we calibrated the compass in various locations. Our final calibration that we used and kept was the furthest away from any potential magnetic fields. Our selected location was on the top floor of the engineering building that was away from any lab rooms or elevators.


<Bullet or Headings of a module>

Unreliable GPS lock

  • Obtaining Coordinates
    • When attempting to obtain coordinates, the GPS module took several minutes in order to connect to a satellite and return coordinates. This process took more time if the GPS module was in a building or in a non-open area.
    • Information from the GPS module was delivered at a rate of 1 Hz. When this information arrived, there were several possibilities such as $GPGGA, $GPGSV, and $GPRMC.
      • Coordinates were only obtained when $GPRMC messages were sent and it yielded an Active (A) coordinate.
      • There was no way to manipulate the GPS module to only send $GPRMC messages.
  • Parsing Data
    • All messages are appended with a new line "\r\n" at the end allowing it to be perfect candidates for the UART gets function. To help with consistency, the gets function was only called when there were characters in the queue to prevent the read from being timed out.
    • Occasionally, some messages become cut off and merged with the next message. This skewed readings as commas were used to separate different sections of the data, including instances where $GPRMC was sent.
    • To save resources, coordinates were only calculated when $GPRMC messages were sent with an (A) status message. This data is presented in a degree, minute, second format as opposed to the decimal format used by the SJOne and the mobile application. As a fail safe, converted coordinates were only saved and sent if the value yielded a latitude between 37 and 38 degrees and a longitude between -122 and -121 degrees.




Comms ECU & LCD

The Comms module source code includes the code for the ESP32 WiFi device and LCD display. Below is the block diagram for this module's connections.

Figure X: Comms module diagram with LCD

Hardware Design

ESP32 WiFi Module

LCD Display

The LCD display used is a 2.4" TFT display made by Adafruit. This display uses either the 8-bit or SPI protocol to transfer data. For this application, the SPI protocol was used in combination with an additional Data/Command line to distinguish between command packets (pulled low) or data packets (pulled high). The display is then connected via a controller that determines what pixels to activate and color. The controller itself uses the I2C protocol to communicate with the Comms board.


Software Design

<List the code modules that are being called periodically.>

ESP32 WiFi Module

LCD Display

The main elements we wanted to be able to see on the car were speed and destination. Destination is displayed in Lat/Long decimal degree coordinates and speed is in kilometers per hour. In addition, we also show the distance between our car and the destination and our current heading from due north. Due to the complexity of the display, each pixel requires about 7 bytes to activate, the possibility of overrunning the scheduler was high. As such, a controller was inserted to perform the actual data transfer to write pixels. The Comms module simply tells the controller what to update, via I2C, from the 1Hz periodic function. To make writing pixels a little easier, the Adafruit GFX Library was used to create fonts, lines, and the triangles used to mimic a compass.

Figure X: LCD display

There are five basic functions used to update the display, four are used to set values to a data struct and the fifth sends the data over I2C:

  • set_display_waypoint() - packages the latitude and longitude destination struct values as a C-string
  • set_display_speed() - packages the car's current speed struct value in a C-string.
  • set_display_distance() - packages the distance remaining between the car and the destination in a C-string
  • set_display_arrow() - selects which heading arrow the display should draw: N, S, E, W, NW, NE, SW, or SE
  • updateDisplay() - sends the full struct that has been prepared by the above functions over I2C


Technical Challenges

<Bullet or Headings of a module>

ESP32 WiFi Module

LCD Display

Originally the plan was to use a 2.2" TFT display by QVGA. This display had been used in previous projects before, however, in this project there was nothing but problems. The SPI communication from the SJOne board was not being received or sent by the display. When testing on a known board and the Adafruit library, the SPI comms would respond, but nothing would actually display on the screen. Assuming this particular display had been compromised, additional displays were purchased with the same results. After much Googling and more research, it turned out that this particular display is known for failures and inconsistencies. The Adafruit display was the original the QVGA was based on. Once that was purchased and tested, there were no further issues, both SPI communications and the display worked fine.

Insane Bug

<Problem Summary> <Problem Resolution>



Driver Module

Driver module source code can be found on GitLab here.

Figure X: Comms module diagram with LCD

Hardware Design

The Driver design has very little going on. Other than the CAN transceiver, the only other connected components are a few op-amps that in turn are connected to the LiPo batteries. These are to monitor the battery life, if power falls below the threshold the Driver can send a message to let us know. In addition, an external monitor is attached to the battery with a buzzer. It also watches the threshold and will emit an alarm when the power dips below it.

Software Design

The main purpose of the Driver is to gather the information from Avoidance and tell the Motor in which direction to go based on that information. A vector algorithm is used to compare all the measurements received and finding the smallest value, directs the car to move away from it.

  • 100Hz periodic
    • check_CAN_messages() - as the name suggests, this function checks the registers to see if any CAN messages were received and pulls the needed data from them.
  • 10Hz periodic
    • check_for_collision() - after data has been stored in the AVOIDANCE struct, this function runs the vector algorithm and populates an array of velocities available.
    • set_velocity() - picks the best option from the array of populated velocities
  • 1Hz periodic
    • set_manual() - checks if manual mode has been selected, this is mostly used for testing and resetting to a known state.
    • send_reset() - checks the status of CAN and if it needs to be, resets the bus
    • set_heartbeat() - sends out a blank message to keep all the other modules in check


Technical Challenges

<Bullet or Headings of a module>

  • vector array -

Improper Unit Testing

<Problem Summary> <Problem Resolution>



Mobile Application

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

<Bullet or Headings of a module>

Wifi Link Reliability

<Problem Summary> <Problem Resolution>



Conclusion

<Organized summary of the project>

<What did you learn?>

Project Video

Project Source Code

https://gitlab.com/cant-bus/cant-bus

Advise for Future Students

<Bullet points and discussion>

Acknowledgement

References

[1] MPU-9255 Data Sheet

[2] MPU-9255 Register Map

[3] Magnetometer Data Sheet