Tilt Motion Controlled LED Alarm Clock

From Embedded Systems Learning Academy
Revision as of 05:47, 17 April 2015 by 146 user9 (talk | contribs) (Parts List & Cost)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Project Title

Abstract

This section should be a couple lines to describe what your project does.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

  • Navleen Johal
  • Ann Varakukala
  • David Whiting

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Week# Date Task Actual
1 4/6-4/12 Continue to conduct research necessary for the project.

Understand the schematics of each part. Design the schematics for project.

Parts were received and team members looked over the schematics of the necessary parts and designed the schematics for the project.
2 4/13-4/19 Build the schematics and check if the leds on the board light up.

Test to see if individual bits light up. Understand how to control the red, green, and blue leds on the board.

3 4/20-4/26 Continue to work on building the project by connecting to SJ One Board.

Program GPIO pins to control the rows on the 8X8 Led Board

4 4/27-5/3 Program to display time on board.

Program push buttons for setting hours and minutes, AM and PM

5 5/4-5/10 Continue to program to display time.

Tilt SJ One Board to change hours and minutes for setting the alarm. Program the buzzer to turn on when alarm time is reached

6 5/11-5/17 Add and program additional sensors. Begin testing.
7 5/18-5/24 Final Testing and Debugging
8 5/25 Demo Day

Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Quantity Item Description Cost
1 SJ One Board $80.00
1 8X8 RGB LED Board $7.50
3 SN74HC595 Shift Register $1.05
24 220 Ohm Resistors $0.20
1 Jumper Wires One large pack of multicolored female-to-female jumper wires $6.00
$
$
$

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

My Issue #1

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.